d1067 rev:a 2fyj 2011-01-01 dms microelectronic limited 1 description the dms1067 is a monolithic step-down switch mode converter with a built in internal power mosfet. it achieves 2a continuous output cur- rent over a wide input supply range with excel- lent load and line regulation. the dms1067 requires a minimum number of readily available standard external components. current mode operation provides fast transient response and e ases loop stabilization. fault condition protection includes cycle-by- cycle current limiting and thermal shutdown. in shutdown mode the regulator draws 25a of supply current. features ? 2a output current ? 0.22 ? internal power mosfet switch ? stable with low esr output ceramic ca- pacitors ? up to 95% efficiency ? 25a shutdown mode ? fixed 420khz frequency ? thermal shutdown ? cycle-by-cycle over current protection ? wide 4.75 to 25v operating input range ? output adjustable from 1.22v to 21v ? programmable under voltage lockout applications ? distributed power systems ? battery chargers ? pre-regulator for linear regulators ? pc monitors package reference part number package temperature DMS1067S soic8 ?40 c to +125 c dms1067p pdip8 ?40 c to +125 c dms1067 4.75 to 25
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 2 absolute maximum ratings (1) supply voltage (v in )..................................... 27v switch voltage (v sw )................ ?1v to v in + 1v bootstrap voltage (v bs ) ...vsw-0.3v to v sw + 6v enable/uvlo voltage (v en )...........?0.3v to +6v comp voltage (v comp ) ...................?0.3v to +6v feedback voltage (v fb ) ................?0.3v to +6v junction temperature ........................... +150 c lead temperature ................................. +260 c storage temperature.............. ?65c to +150 c recommended operating conditions (2) input voltage (v in ) ......................... 4.75v to 25v operating temperature...............?40 c to +125 c thermal resistance (3) ja jc soic8 .................................... 105..... 50... c/w pdip8 ...................................... 95?...55.. c/w notes: 1) exceeding these ratings may damage the device. 2) the device is not guaranteed to function outside of its operating conditions. 3) measured on approximately 1? square of 1 oz copper. electrical characteristics v in = 12v, v en = 5v,t a = +25 c, unless otherwise noted. parameter condition min typ max units feedback voltage 4.75v v in 25v 1.184 1.222 1.258 v upper switch-on resistance 0.22 ? lower switch-on resistance 10 ? upper switch leakage v en = 0v, v sw = 0v 10 a current limit 2.4 3.1 a oscillator frequency 370 420 470 khz short circuit frequency v fb = 0v 42 khz maximum duty cycle v fb = 1.0v 90 % minimum duty cycle v fb = 1.5v 0 % en shutdown threshold voltage i cc > 100a 2.0 2.3 2.5 v en uvlo threshold rising v en rising 2.0 2.5 3.0 v en uvlo threshold hysteresis 200 mv enable pull-up current v en = 0v 2 a supply current (shutdown) v en 0.4v 25 50 a supply current (quiescent) v en 2.6v, v fb = 1.4v 1.0 1.5 ma thermal shutdown 160 c
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 3 pin functions pin # name description 1 bs high-side gate drive boost input. bs supplies the drive for the high-side n-channel mosfet switch. connect a 10nf or greater capacitor from sw to bs to power the switch. 2 in power input. in supplies the power to the ic, as well as the step-down converter switch. drive in with a 4.75 to 25v power source. bypass in to gnd with a suitably large capaci- tor to eliminate noise on the input to the ic. see input capacitor. 3 sw power switching output. sw is the switching node that supplies power to the output. connect the output lc filter from sw to the output load. note that a capacitor is required from sw to bs to power the high-side switch. 4 gnd ground. 5 fb feedback input. fb senses the output voltage to regulate that voltage. drive fb with a resistive voltage divider from the output voltage. the feedback threshold is 1.222v. see setting the output voltage. 6 comp compensation node. comp is used to compensate the regulation control loop. connect a series rc network from comp to gnd to compensate the regulation control loop. see compensation. 7 en enable input. en is a digital input that turns the regulator on or off. drive en high to turn on the regulator, low to turn it off. for automatic startup, leave en unconnected. 8 nc no connect.
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 4 operation the dms1067 is a current-mode step-down switch-mode regulator. it regulates input voltages from 4.75v to 25v down to an output voltage as low as 1.222v and is able to supply up to 2a of load current. the dms1067 uses current-mode control to regulate the output voltage. the output voltage is measured at fb through a resistive voltage divider and amplified through the internal error amplifier. the output current of the trans- conductance error amplifier is presented at comp where a network compensates the regu- lation control system. the voltage at comp is compared to the switch current measured inter- nally to control the output voltage. the converter uses an internal n-channel mosfet switch to step down the input voltage to the regulated output voltage. since the mosfet requires a gate voltage greater than the input voltage, a boost capacitor connected between sw and bs drives the gate. the ca- pacitor is internally charged while the switch is off. an internal 10 ? switch from sw to gnd is used to ensure that sw is pulled to gnd when the switch is off to fully charge the bs capacitor. figure 1 ? functional block diagram 42-450khz
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 5 application information component selection setting the output voltage the output voltage is set using a resistive volt- age divider from the output voltage to fb (see typical application circuit on page 1). the volt- age divider divides the output voltage down by the ratio: where v fb is the feedback voltage and v out is the output voltage. thus the output voltage is: r2 can be as high as 100kq, but a typical value is 10k ? . using that value, r1 is determined by: for example, for a 3.3v output voltage, r2 is 10k ? , and r1 is 16.9k ? . inductor the inductor is required to supply constant cur- rent to the output load while being driven by the switched input voltage. a larger value inductor results in less ripple current that results in lower output ripple voltage. however, the larger value inductor has a larger physical size, higher series resistance and/or lower saturation current. choose an inductor that does not saturate under the worst-case load conditions. a good rule for determining the inductance is to allow the peak- to-peak ripple current in the inductor to be ap- proximately 30% of the maximum load current. also, make sure that the peak inductor current (the load current plus half the peak-to-peak in- ductor ripple current) is below the 2.4a minimum current limit. the inductance value can be calculated by the equation: where v in is the input voltage, f is the switching frequency, and l is the peak-to-peak inductor ripple current. table 1 lists a number of suitable inductors from vari- ous manufacturers. table 1?inductor selection guide vendor/ model core type core ma- terial package dimensions (mm) w l h sumida cr75 open ferrite 7.0 7.8 5.5 cdh74 open ferrite 7.3 8.0 5.2 cdrh5d28 shielded ferrite 5.5 5.7 5.5 cdrh5d28 shielded ferrite 5.5 5.7 5.5 cdrh6d28 shielded ferrite 6.7 6.7 3.0 cdrh104r shielded ferrite 10.1 10.0 3.0 toko d53lc type a shielded ferrite 5.0 5.0 3.0 d75c shielded ferrite 7.6 7.6 5.1 d104c shielded ferrite 10.0 10.0 4.3 d10fl open ferrite 9.7 1.5 4.0 coilcraft do3308 open ferrite 9.4 13.0 3.0 d03316 open ferrite 9.4 13.0 5.1 input capacitor the input current to the step-down converter is dis- continuous, and therefore an input capacitor c1 is required to supply the ac current to the step-down converter while maintaining the dc input voltage. a low esr capacitor is required to keep the noise at the ic to a minimum. ceramic capacitors are preferred, but tantalum or low-esr electrolytic capacitors may also suffice. the input capacitor value should be greater than 10uf. the capacitor can be electrolytic, tantalum or ceramic. however, since it absorbs the input switch- ing current it requires an adequate ripple current rat- ing. its rms current rating should be greater than ap- proximately 1/2 of the dc load current. for insuring stable operation, c2 should be placed as close to the ic as possible. alternately a smaller high quality ceramic 0.1 uf capacitor may be placed closer to the ic and a larger capacitor placed further away. if using this technique, it is recommended that the lar- ger capacitor be a tantalum or electrolytic type. all ceramic capacitors should be placed close to the dms1067.
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 6 output capacitor the output capacitor is required to maintain the dc output voltage. low esr capacitors are preferred to keep the output voltage ripple low. the characteristics of the output capacitor also affect the stability of the regulation control sys- tem. ceramic, tantalum or low esr electrolytic capacitors are recommended. in the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capaci- tance and so the output voltage ripple is mostly independent of the esr. the output voltage ripple is estimated to be: in the case of tantalum or low-esr electrolytic capacitors, the esr dominates the impedance at the switching frequency, and so the output ripple is calculated as: v ripple ? i x r esr output rectifier diode the output rectifier diode supplies the current to the inductor when the high-side switch is off. to reduce losses due to the diode forward voltage and recovery times, use a schottky rectifier. table 2 provides the schottky rectifier part numbers based on the maximum input voltage and current rating. tab l e 2?schottky rectifier selection gu i de 2a load current v in (max) part number vendor 15v 30bq015 4 b220 1 sk23 6 20v sr22 6 20bq030 4 b230 1 sk23 6 26v sr23 3,6 table 3 lists some rectifier manufacturers. table 3?schottky diode manufacture choose a rectifier the maximum reverse voltage rat- ing of which is greater than the maximum input volt- age, and has a current rating greater than the maxi- mum load current. compensation the system stability is cont rolled through the comp pin. comp is the output of the internal transconduc- tance error amplifier. a series capacitor-resistor combination sets a pole-zero combination to control the characteristics of the control system. the dc loop gain is: where a vea is the transconductance error amplifier voltage gain (400v/v), gcs is the current sense gain (roughly the output current divided by the voltage at comp) equal to 1.95 a/v and r load is the load resis- tance (v out / i ou t where i 0 ut is the output load current). the system has two poles of importance, one is due to the compensation capacitor (c3), and the other is due to the output capacitor (c2). these are: where p1 is the first pole and g ea is the error ampli- fier transconductance (770ua/v). the other pole is: the system has one zero of importance, due to the compensation capacitor (c3) and the compensation resistor (r3). the zero is: if a large value capacitor (c2) with relatively high equivalent-series-resistance (esr) is used, the zero due to the capacitance and esr of the output capaci- tor can be compensated by a third pole set by r3 and c6: the system crossover frequency (the frequency where the loop gain drops to 1 or odb) is important. a good rule of thumb is to set the crossover fre- quency to approximately 1/10 of the switching fre- quency. in this case, the switching frequency is 450khz. therefore, use a crossover frequency (fc) of 40khz. lower crossover frequencies result in slower response and worse transient load recovery. higher crossover frequencies can result in instability. vendor web site diodes, inc. www.diodes.com fairchild semiconductor www.fairchildsemi.com general semiconductor www.gensemi.com international rectifier www.irf.com on semiconductor www.onsemi.com pan jit international www.panjit.com.tw
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 7 choosing the compensation components the values of the compensation components given in table 4 yield a stable control loop for the output voltage and capacitor given. table 4?compensation values for typical output voltage/capacitor combinations vou c2 r1 c3 c6 2.5v 22uf ceramic 7.5k ? 2.2nf none 3.3v 22uf ceramic 10k ? 2nf none 5v 22uf ceramic 15k ? 1.2nf none 12v 22uf ceramic 33k ? 1nf none 2.5v 560uf/6.3v (30m ? esr) 200k ? 1nf 100pf 3.3v 560uf/6.3v (30m ? esr) 200k ? 1nf 82pf 5v 470uf/10v (30m ? esr) 250k ? 1nf 56pf 12v 220uf/25v (30m ? esr) 250k ? 1nf 27pf to optimize the compensation components for conditions not listed in table 4, use the following procedure: choose the compensation resistor to set the de- sired crossover frequency. determine the value by the following equation: putting in the know constants and setting the crossover frequency to the desired 40khz: choose the compensation capacitor to set the zero below 1/4 of the crossover frequency. determine the value by the following equation : determine if the second compensation capacitor, c6, is required. it is required if the esr zero of the output capacitor occurs at less than four times the crossover frequency. or if this is the case, add the second compensation capacitor. determine the value by the equation: , where r esr(max) is the maximum equivalent series resistance of the output capacitor. for example: v qut = 3.3v c2 = 22ufceramic(esr = 10m ? ) r3 (1.37 x 10 8 )x (22 x 10 -6 )x 3.3 = 9.9k ? use the nearest standard value of 10k ? c3>(0.22x(22x10 -6 )x3.3/(10x10 3 )=1.6nf use a standard value of 2nf. 2 x c2 x r esr x f c =0.014 wich is less than 1, therefore no second compen- sation capacitor is required. table 5 ? recommended components for stan- dard output voltage v out r1 l1 minimum 1.22v 0 ? 6.8uh 1.5v 2.32 k ? 6.8uh 1.8v 4.75 k ? 10uh 2.5v 10.5 k ? 10uh 3.3v 16.9 k ? 15uh 5.0v 30.9 k ? 22uh negative output voltage the dms1067 can be configured as a buck-boost regulator to supply negative output voltage. because the gnd pin of the ic is now connected to negative output voltage, the maximum allow- able input voltage is the ic input voltage rating (25v) minus the negative output voltage value. a typical application circuit is shown in figure 3. external bootstrap diode it is recommended that an external bootstrap di- ode be added when the system has a 5v fixed input or the power supply generates a 5v output. this helps improve the efficiency of the regulator. the bootstrap diode can be a low cost one such as in4148 or bat54. this diode is also recommended for high duty cycle operation (when (v out / v in ) >65%) and high output voltage (v out >12v) applications dms1067
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 8 typical application circuits figure 3?application circuit for -5v supply dms1067
tm d1067 rev: a2fyj 2011-01-01 dms microelectronic limited 9 package information
|
